e dot dot dot
a mostly about the Internet blog by

home << Woodworking
October 2018
Sun Mon Tue Wed Thu Fri Sat
 
     


XPanel: The First Open Source Panel Saw Jig - Part 1

I'm an IT guy, so I'm very familiar with the concept of open source software, and I love the idea. So, here's my contribution to the relatively new open source "hardware" movement.

I've always been interested in woodworking to some extent, so was my father, and so was my grandfather, and up until recently it was my grandfather who had the most extensive home shop, and in his day, was probably the most avid woodworker among us (for the record, neither my father nor my grandfather are still around.)

But during the past year or so I've started getting into woodworking more seriously, and like a lot of new or rediscovering hobbyist woodworkers, I've spent most of my time so far just "setting up shop." I've discovered that one of the most frustrating and difficult things to do in a home shop, is breaking down full 4'x8' sheet stock panels, or large cutoffs of sheet stock, into smaller project pieces.

I've priced the ready made prefabricated panel saws that can be found online, and they're way out of range for most home shops (certainly mine) and I've wrestled with taking on one of the many DIY versions to be found online as well, but even the kits for them are expensive, and the work involved in a version built from scratch with plans is daunting.

The whole time I've been looking around for some sort of panel sawing solution, I've always thought if I had it my way, I'd want something that satisfied what I considered to be several important requirements for hobbyist woodworkers, as follows:

- it must be makeable from inexpensive (i.e. cheap), readily available materials
- it must be quickly assembled and disassembled for storage
- it must not take up much room, whether assembled or stored
- it must go together without permanent fasteners, so as to make it easy to swap out worn pieces (clamps or notches are the preferred methods of fastening for sacrificial pieces)
- pieces that won't ever be cut into, can have permanent fasteners and extensions attached
- occasionally used add-on or attachment pieces, can have permanent fasteners and extensions attached
- it must be functionally flexible and easily modified

So while surfing around one night looking for yet another panel sawing suggestion, I stumbled upon something I thought might be a solution
for my home shop. It was nothing more than just a cheap pair of 2"x4"x8' studs, assembled in an "X" pattern, and fastened together using angled notches in the center edge of each stud. It could be placed on the floor, and it could support even a full 4'x8' sheet of anything for cutting. The idea was to set the blade as high as possible while still cutting through the material, but scoring the supporting X'd 2by's as little as possible.

This idea was good, and it satisfied some of my requirements, but it lacked something to make it a great idea.

Behold what I call the XPanel jig. I refer to it as a jig rather than a panel saw, because it behaves and is used much more as a jig is used. Here are pictures with and without an almost full-size sheet on the jig (ignore the incredible amount of junk around it.)





My addition of the vertical studs on each side has made it so the jig can be placed against a wall, and used similar to the way a "real" panel saw is used, and it all goes together and comes apart quickly, and by way of the angled notches, without the use of permanent fasteners. And the addition of a clamped deck rail makes it so a panel can be loaded onto the jig easily, without adding a permanent part to the jig. Here are pics of the angled notches for the vertical members.

IMAGE(S) TO COME


Here's the link to the original "X" jig page again.


I also made three different size circular saw guides, similar to the popular version(s) found on woodworking sites around the internet. Here they are:

IMAGE(S) TO COME

Here is the jig with various size sheets, and with the guides in place:

IMAGE(S) TO COME

The ultimate advantage of this jig is this... EVERY CUT IS PERFORMED HORIZONTALLY, allowing gravity to do most of the work, and eliminating the need for any sort of counterweight system to support the saw during vertical cuts. Here's a picture of how that's accomplished:

IMAGE(S) TO COME

In keeping with the open source concept of this jig, it's flexibility is only limited by your imagination, and my original requirements. I'll be posting pics of some of the compliant "plug-ins" (i.e add-ons and attachments), I've come up with to make the jig even sweeter.

And by all means, if you can think of anything to make the jig even more useful, feel free to comment or ask questions, and of course, I encourage you to make and use the jig and see for yourself how this incredibly simple design just may solve your panel cutting needs at a fraction of the cost of other solutions.



MORE TO FOLLOW...


posted at: 12:10am on 23-Jan-2013
path: /Woodworking | permalink | edit (requires password)

0 comments, click here to add the first


home << Woodworking

October 2018
Sun Mon Tue Wed Thu Fri Sat
 
     







RSS (site)  RSS (path)

ATOM (site)  ATOM (path)

Categories
 - blog home

 - Announcements  (2)
 - Annoyances  (0)
 - Career_Advice  (1)
 - Domains  (0)
 - Downloads  (4)
 - Ecommerce  (2369)
 - Fitness  (0)
 - Home_and_Garden  (0)
     - Cooking  (0)
     - Tools  (0)
 - Humor  (1)
 - Notices  (0)
 - Observations  (1)
 - Oddities  (2)
 - Online_Marketing  (3420)
     - Affiliates  (1)
     - Merchants  (1)
 - Policy  (1006)
 - Programming  (0)
     - Browsers  (1)
     - DHTML  (0)
     - Javascript  (536)
     - PHP  (0)
     - PayPal  (1)
     - Perl  (37)
          - blosxom  (0)
     - Unidata_Universe  (18)
 - Random_Advice  (1)
 - Reading  (0)
     - Books  (0)
     - Ebooks  (1)
     - Magazines  (0)
     - Online_Articles  (4)
 - Resume_or_CV  (1)
 - Reviews  (1)
 - Rhode_Island_USA  (0)
     - Providence  (1)
 - Shop  (0)
 - Sports  (0)
     - Football  (1)
          - Cowboys  (0)
          - Patriots  (0)
     - Futbol  (1)
          - The_Rest  (0)
          - USA  (1)
 - Woodworking  (1)


Archives
 -2018  October  (31)
 -2018  September  (47)
 -2018  August  (46)
 -2018  July  (46)
 -2018  June  (51)
 -2018  May  (49)
 -2018  April  (69)
 -2018  March  (79)
 -2018  February  (65)
 -2018  January  (79)
 -2017  December  (75)
 -2017  November  (59)


My Sites

 - Millennium3Publishing.com

 - SponsorWorks.net

 - ListBug.com

 - TextEx.net

 - FindAdsHere.com

 - VisitLater.com